---
title: "What Is a TPO Roof? TPO vs PVC and EPDM | Global Green Roofing"
description: "What is a TPO roof? The heat-welded single-ply membrane explained: how it goes on, TPO vs PVC and EPDM, what shortens its life, and Title 24."
source: https://globalgreenroofing.com/roofing-guides/what-is-a-tpo-roof/
---

# What Is a TPO Roof, and How Does It Compare with PVC and EPDM?

By **[Global Green Roofing](https://globalgreenroofing.com/author/global-green-roofing-team/)**Published November 6, 2026Updated November 6, 2026

**What is a TPO roof? It is a single-ply roof membrane made of thermoplastic polyolefin, rolled out in wide sheets whose seams are heat-welded into one continuous surface.** It covers flat and low-slope roofs. White TPO reflects most of the sun, which is why it is common in California, where Title 24 sets cool-roof values for low-slope re-roofs.

Its two rivals are also single-ply sheets. PVC is heat-welded too, and one major maker lists its resistance to chemicals, grease and animal fat. EPDM is a cured rubber, usually black, so its seams are spliced with tape instead of welded, and it has to be made white or coated to count as a cool roof.

## What does TPO stand for, and what is the membrane made of?

TPO stands for thermoplastic polyolefin. Its ASTM standard, D6878, covers a flexible sheet with TPO as the principal polymer, "intended for use in single-ply roofing membranes exposed to the weather", and it requires a reinforcing fabric or scrim inside the sheet. In a typical product a polyester fabric is sealed between a top and a bottom TPO ply; one maker describes the blend as "the flexibility of ethylene-propylene (EP) rubber with the heat weldability of polypropylene".

**Thermoplastic** is the word that matters on the roof. The sheet softens under heat and fuses as it cools, so two overlapping sheets become one piece. PVC shares that property; EPDM, a vulcanized rubber, does not, which is why its seams are spliced, typically with seam tape.

Sheets are sold in 45, 60 and 80 mil (thousandths of an inch). In one manufacturer's data the thicker sheets carry more material over the scrim and stayed watertight under harder impacts in its puncture test. The standard itself sets only minimum properties: fire resistance, field seam strength and wind uplift of the finished roof are, in its words, "beyond the scope", so a proposal should name the tested system, not only the membrane.

## How is a TPO roof installed?

The old roof comes off (or is checked for a recover), insulation and a cover board go down, then the sheets are laid and held in one of three ways:

-   **Mechanically fastened:** plates and screws hold each sheet along its edge, and the next sheet laps over them and is welded on top.
-   **Fully adhered:** the sheet is bonded to the board below with adhesive. The Department of Energy notes that adhesives need a minimum temperature to bond, and a reflective roof stays cooler, so adhered cool roofs may need warmer days to install.
-   **Induction welded:** induction welding plates are fastened down first, and an induction tool, set on the membrane over each plate, welds the sheet to it.

Every lap is then welded with hot air, usually by an automatic welder that rides along the seam, and the finished seams are probed. A sheet that has sat out in the weather is cleaned with a membrane cleaner before it is welded. Where the roof meets a parapet wall, a curb, a skylight, a drain or a pipe, pieces of TPO flashing are welded to the field sheet. Those details and the seams, more than the open field of the roof, are where TPO roofs leak.

Planning a new flat or low-slope roof? Our [flat roofing](https://globalgreenroofing.com/our-services/flat-roofing/) service installs TPO and other membranes, with tapered insulation, crickets and drains planned before the membrane. For a shop, office or multi-unit building, see [commercial roofing](https://globalgreenroofing.com/our-services/commercial-roofing/).

## TPO vs PVC vs EPDM

All three are single-ply sheets for low-slope roofs. They differ in what they are made of, how the seams are joined and how much sun they reflect:

TPO vs PVC vs EPDM roofing membranes

|  | TPO | PVC | EPDM |
| --- | --- | --- | --- |
| Material (ASTM standard) | Thermoplastic polyolefin, always reinforced (D6878) | Poly(vinyl chloride), always reinforced (D4434) | Vulcanized EPDM rubber, reinforced or not (D4637) |
| Seams | Heat-welded with hot air | Heat-welded with hot air | Spliced, typically with seam tape |
| Usual color | White; also tan, gray and other colors | Usually white | Black; also made in white |
| Reflectance | White is reflective without a coating | White is reflective without a coating | Black must be made white or coated to reflect |
| What one major maker stresses | High reflectivity and welded seams | Resistance to chemicals, grease, fire and animal fat | Track record: black for more than 50 years, white for more than 30 |
| Typical use | Flat roofs of homes, additions and commercial buildings | Roofs where its chemical and grease resistance is wanted | Low-slope roofs; its makers say black sheets help melt frost, dew and ice |

Each row describes the membrane type. Fire rating, wind uplift, hail rating and warranty belong to a named product installed as a tested system (a flat roof membrane is Class A only as a tested assembly, as our guide to [Class A fire-rated roofing](https://globalgreenroofing.com/roofing-guides/class-a-fire-rated-roofing/) explains), so compare the products named in each proposal.

## How long does a TPO roof last?

No standards body publishes a life in years for TPO. SPRI, the association of single-ply membrane makers, says that "no guarantee of length of life of any roofing product can be made". Manufacturers sell warranties with set terms, but the Department of Energy warns that a warranty "may not necessarily tell the entire story": a material warranty usually does not cover the seams, "where premature failure can occur".

What decides the life of a TPO roof is mostly the installation and the roof under it:

-   **Seams:** a full weld on every lap, probed afterwards. Membrane that has weathered is cleaned before it is hot-air welded, so a repair on an older roof starts with cleaning.
-   **Details:** the flashing at walls, curbs, skylights, drains and pipes, where most leaks start.
-   **Standing water:** the benchmark of the National Roofing Contractors Association, as quoted by the Florida Roofing and Sheet Metal Contractors Association, is no ponding water 48 hours after rain, so slope, crickets and drains are fixed before the membrane goes on.
-   **Heat:** one maker caps the sustained temperature of its TPO at 160°F (71°C) and notes that oxidation, a main way roofing breaks down, roughly doubles for each 18°F (10°C) rise in membrane temperature. A light surface that stays cooler ages more slowly.
-   **Thickness:** 60 and 80 mil sheets have more material over the scrim to wear through than 45 mil.

Lifespans of other roof types, by material, are in [how long does a roof last](https://globalgreenroofing.com/roofing-guides/how-long-does-a-roof-last/).

## TPO and the California cool-roof rule for low-slope roofs

In California, a low-slope re-roof usually has to meet the Title 24 cool-roof values. On a home, replacing "more than 50 percent" of a low-slope roof (the Energy Commission's forms say 50 percent or more) in climate zones 4 and 6 to 15 calls for an aged solar reflectance of at least 0.63 and a thermal emittance of at least 0.75, or a Solar Reflectance Index (SRI) of 75 (Section 150.2(b)1I).

On a commercial building the same low-slope values apply in every climate zone once more than 50 percent of the roof, or more than 2,000 square feet, whichever is less, is replaced, recovered or recoated (Section 141.0(b)2B). Both rules have exceptions, and both let added roof insulation make up for a lower reflectance (Tables 150.2-E and 141.0-B).

The values are the **aged** ones, measured after three years outdoors and published by the Cool Roof Rating Council (CRRC). Color decides the result. One manufacturer's CRRC-rated TPO line shows it:

Aged CRRC values of one TPO product line, by color

| Color | Aged solar reflectance | Aged thermal emittance | Aged SRI | Meets 0.63 and 0.75? |
| --- | --- | --- | --- | --- |
| White | 0.70 | 0.86 | 85 | Yes |
| Tan | 0.64 | 0.87 | 77 | Yes |
| Gray | 0.43 | 0.88 | 49 | No |

Even white TPO loses some reflectance as it weathers (0.79 new against 0.70 after three years in that line), which is why the code uses aged values. Ask for the CRRC rating of the exact product and color in your proposal. Climate zones, exceptions and the insulation trade-off are in our [guide to cool roof requirements in California](https://globalgreenroofing.com/roofing-guides/cool-roof-requirements-california/).

## When does TPO fit a Los Angeles home, addition or commercial building?

Shingles and tile need pitch to shed water, so a flat main roof, a low-slope addition, a garage, a patio cover or a commercial roof takes a membrane. TPO is a strong fit when:

-   The low-slope roof is being replaced where Title 24 applies: a TPO color rated at or above the values (white and tan in the line above) meets them in one layer, with no separate coating.
-   The roof is large: wide sheets mean fewer seams, and one maker counts up to 60 percent fewer seams with 16-foot sheets than with 10-foot ones.
-   You want the seams welded rather than taped.

Compare it with another option when grease or chemicals reach the roof (check PVC and the chemical listing of the exact TPO product), when you want a dark roof (a gray or dark TPO can miss the Title 24 values), or when water ponds: the drainage comes first, whatever the membrane.

For the work itself, see [flat roofing](https://globalgreenroofing.com/our-services/flat-roofing/) for homes and additions and [commercial roofing](https://globalgreenroofing.com/our-services/commercial-roofing/) for commercial buildings. A sound TPO roof with a leak is a [flat roof repair](https://globalgreenroofing.com/our-services/flat-roof-repair/), usually a heat-welded patch.

## Other questions

### Can TPO be used on a house?

Yes, on its flat and low-slope parts: a flat main roof, additions, garages and patio roofs. Pitched sections of the same house keep their shingles or tile.

### Can a TPO roof go over an existing roof?

Sometimes. The California Residential Code allows a recover in limited cases, but not over a water-soaked roof, over slate, clay or cement tile, or over a roof that already has two layers (Section R908.4). Wet insulation has to come out first, so the roof is checked before a recover is proposed.

### Is TPO or EPDM better for a flat roof?

Neither wins everywhere. In Southern California sun, white TPO meets the Title 24 cool-roof values without a coating, while black EPDM must be made white or coated to reflect. EPDM makers point to its long track record. Compare the CRRC values and seam method of each product you are offered.

### Does a TPO roof need a coating?

Not for reflectance: the Department of Energy notes that TPO and PVC membranes are usually white and reflective without extra coatings. Coatings add reflectance only over a sound, dry roof; they do not repair a failing membrane.

Questions about your own roof? Call (323) 760-7835 or [request an estimate](https://globalgreenroofing.com/contact-us/#quote), and see our [flat roofing](https://globalgreenroofing.com/our-services/flat-roofing/) service for what the work involves.

### Sources

12 public sources, tap to show

1.  [ASTM D6878/D6878M-21, Standard Specification for Thermoplastic Polyolefin-Based Sheet Roofing (scope)](https://store.astm.org/d6878_d6878m-21.html)
2.  [ASTM D4434/D4434M-21, Standard Specification for Poly(Vinyl Chloride) Sheet Roofing (scope)](https://store.astm.org/d4434_d4434m-21.html)
3.  [ASTM D4637/D4637M-15(2021), Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane (scope)](https://store.astm.org/d4637_d4637m-15r21.html)
4.  [U.S. Department of Energy, Guidelines for Selecting Cool Roofs (2010)](https://www.energy.gov/sites/prod/files/2013/10/f3/coolroofguide.pdf)
5.  [Carlisle SynTec, Sure-Weld TPO reinforced membrane product data (via BuildSite)](https://www.buildsite.com/pdf/carlislesyntec/Sure-Weld-TPO-Reinforced-Membrane-Product-Data-2929044.pdf)
6.  [Carlisle SynTec, TPO membranes](https://www.carlislesyntec.com/en/Roofing-Products/Membranes/TPO)
7.  [Carlisle SynTec, PVC membranes](https://www.carlislesyntec.com/en/Roofing-Products/Membranes/PVC)
8.  [Carlisle SynTec, EPDM membranes](https://www.carlislesyntec.com/en/Roofing-Products/Membranes/EPDM)
9.  [SPRI (Single Ply Roofing Industry), FAQ](https://www.spri.org/faq/)
10.  [California Energy Commission, 2025 Building Energy Efficiency Standards (CEC-400-2025-010-F), Sections 141.0(b)2B and 150.2(b)1I](https://www.energy.ca.gov/sites/default/files/2025-07/CEC-400-2025-010-F_0.pdf)
11.  [Cool Roof Rating Council, Rated Roof Products Directory](https://coolroofs.org/directory/roof)
12.  [2025 California Residential Code, Chapter 9 (R908.4), via UpCodes](https://up.codes/viewer/california/ca-residential-code-2025/chapter/9/roof-assemblies)

Sources were read on November 6, 2026. Codes and maps change; check with your building department for the rules in force at your address.

## Have a roofer look at your roof

An on-site assessment with photos, and a written proposal before anything is decided.

## Related guides

### [Cool Roof Requirements in California: What Title 24 Asks of a Re-Roof](https://globalgreenroofing.com/roofing-guides/cool-roof-requirements-california/)

Which re-roofs it covers, the values, and the exceptions.

### [How Long Does a Roof Last?](https://globalgreenroofing.com/roofing-guides/how-long-does-a-roof-last/)

Roof lifespan by material, the California fire rule, and the signs it is due.

### [What Is a Class A Fire Rated Roof, and When Does California Require One?](https://globalgreenroofing.com/roofing-guides/class-a-fire-rated-roofing/)

The rating, the roofs that qualify, and when it applies.

Contact us

## Let's talk roofs

Tell us what is going on with your roof. We will schedule an on-site assessment and send a written proposal before anything is decided.

**Call**(323) 760-7835**Email**info@globalgreenroofing.com

**Serving**Los Angeles, Ventura and Santa Barbara Counties

**Hours**Every day: 8 AM to 9 PM
